Welcome to LuphiTouch®!
Today is 2026.11.09 , Monday
Leave Your Message
News Categories
    Featured News

    How can the quality of the silver paste used in membrane switches be determined as good or bad?

    2026-05-25

    To assess the quality of silver paste, a comprehensive judgment needs to be made from three aspects: appearance, performance, and process compatibility. Here are the most practical identification methods in the industry:

    productive process (1).jpg
    1. Appearance and Physical Properties (Initial Screening)
    Color: The high-quality silver paste should be silver-gray or silver-white, with uniform color and no blackening or yellowing. If the color is too dark, it may indicate oxidation of the silver powder or excessive impurities; if it is too yellow, it may indicate abnormal resin ratio.
    Viscosity: Use a stirring rod to pick up the silver paste and observe its flow state. High-quality silver paste should be fine, uniform, without a gritty feel, and have moderate fluidity (similar to thick yogurt). If there are lumps, stratification, or precipitation, it indicates that the silver paste has deteriorated or the formula is unstable.
    Fineness: Test with a scraping fineness meter (such as a Heegman fineness meter). The fineness of high-quality silver paste should be ≤ 10 μm. The finer the fineness, the finer the printed lines and the better the conductivity.
    Odor: The normal odor of the silver paste is mild and non-irritating. If a pungent sour smell or solvent smell is detected, it may indicate a chemical reaction or the use of inferior solvents.
    2. Conductive Performance (Core Indicator)
    This is the most crucial parameter for evaluating the quality of silver paste, and it directly determines the reliability of the conductive performance of the membrane switch.Sheet Resistance: This is the most direct indicator of conductivity. The sheet resistance of high-quality silver paste should be ≤ 50 mΩ/□ (at a film thickness of 25 μm). The lower the sheet resistance, the better the conductivity.
    Testing method: Use a four-probe resistance tester to measure under standard conditions (temperature 25℃, humidity 50%). 
    Volume Resistivity: This is a more precise indicator of conductivity. The volume resistivity of high-quality silver paste should be ≤ 5×10⁻⁵ Ω·cm.
    Silver content: This is the fundamental factor affecting conductivity. The silver content of high-quality silver paste is usually between 60% - 70%. Low silver content leads to poor conductivity; while high silver content (>80%), the adhesion will decrease and the cost will increase.

    3. Printing and Process Performance (Production Compatibility)
    Printing property: When printing on a 250-300 mesh screen, the high-quality silver paste should be able to pass smoothly, with clear line edges and no jaggedness, no clogging of the screen, or wire drawing phenomenon.
    Drying/Curing Conditions: The curing conditions for high-quality silver paste are usually 120-150℃ for 10-30 minutes. After curing, the silver film should be smooth, dense, and free of bubbles.
    Adhesion: This is the key factor determining the long-term reliability of the silver paste.
    3M tape test: Pull 3M 600 tape vertically. High-quality silver paste should not have silver powder fall off.
    Grid Test: Use a grid knife to draw 1mm×1mm grids, then pull with tape. The area of detachment should be <5%.
    Weldability: If welding is required later, the silver paste should be able to withstand a welding temperature of 260℃ for 10 seconds without bubbling or detachment.

    4. Environmental Reliability (Long-term Stability)
    Resistance to Heat and Humidity: After being placed at 85℃/85%RH for 1000 hours, the resistance value change should be less than 20%. This is a key indicator for evaluating the long-term stability of the silver paste in a high-humidity environment.
    Resistance to Salt Spray: After being exposed to 5% NaCl salt spray for 48 hours, the silver film should show no corrosion or discoloration.
    Resistance to Temperature Variation: After cycling between -40℃ and 85℃ for 500 times, the resistance value change should be less than 10%.

    5. Practical Suggestions
    Selecting Suppliers: Choose silver paste agents and distributors. It is recommended to prefer agents with original factory authorization to avoid purchasing counterfeit or inferior products.
    Requesting Reports: Require the supplier to provide third-party test reports, including key indicators such as sheet resistance, silver content, adhesion, and resistance to humidity and heat.
    Sampling Testing: Before large-scale procurement, it is essential to conduct small-scale sampling tests to verify the compatibility of the silver paste with your substrate (PET/PI) and printing process (screen mesh size, curing temperature).
    Monitoring Batch Consistency: There may be differences in performance among different batches of silver paste. It is recommended to request the supplier to provide a batch consistency report and keep each batch's samples for future reference.
    Summary: Quick Judgment Table for Silver Paste Quality

    Test items High-quality silver paste Low-quality silver paste
    Color Silver gray/silver white, uniform Blackened, yellowish, with impurities
    Viscosity Fine, uniform, no particles Clumped, stratified, precipitated
    Fineness ≤10μm >15μm
    Resistivity     ≤50 mΩ/□ >100 mΩ/□
    Silver content 60%-70% <50% or >80
    Adhesion (3M tape)     No peeling Significant peeling
    Resistance to wet heat (85℃/85%RH/1000h) Resistance variation <20% Resistance variation >50%
    Odor Gentle, non-irritating Strong, pungent smell or solvent smell

    Summary: The key to identifying the quality of silver paste lies in "examining the appearance, measuring the sheet resistance, testing the adhesion, and checking the report". When purchasing, it is crucial to request third-party testing reports and conduct small-scale sample testing to avoid getting into trouble.