Welcome to LuphiTouch®!
Today is 2026.11.09 , Monday
Leave Your Message
News Categories
    Featured News

    How to conduct a lifespan test for backlighting membrane switch?

    2026-06-29

    The life test of the membrane keypad with backlight needs to simultaneously evaluate the mechanical key life and the backlight system life, which is more complex than the test of the backlighting membrane switch. Here is the complete test plan:

    a13.jpg

    Test module division
    The lifespan test for the backlighting membrane switch should be divided into three parallel modules: 

    Test module  Assessment object Core indicators
    Mechanical lifespan  Key components such as key structure, spring, and contacts  Pressing times, contact resistance, operating force
    Backlight lifespan Light sources such as LED/EL/fiber Brightness attenuation, color temperature drift, uniformity
    Overall lifespan Both mechanical and backlight working simultaneously Interaction between the two, thermal accumulation effect

    Mechanical life test Testing equipment
    Using a dedicated key press life testing machine (such as a keyboard strike life testing machine), the key parameters are:

    Test speed: 60 - 300 times/minute (membrane switches are recommended at 60 - 120 times/minute)
    Pressure range: 50 - 500 gf, with an accuracy of ±1%
    Test count setting: Up to 99,999,999 times
    Multi-station simultaneous testing to enhance efficiency

    Test parameter settings

    Parameter  Recommended value  Explanation
    Pressing force  Rated force + 25%  If the rated force is 200gf, set it to 250gf
    Pressing frequency 60~120 times/minute  Pressing too fast may cause temperature rise and affect the results
    Environmental temperature 23 ± 2°C Standard laboratory conditions
    Relative humidity 50 ± 5%   Standard laboratory conditions
    Test times  500,000~1,000,000 times  Industrial grade usually requires 1,000,000 times

    Criteria for judgment
    After 1 million tests are completed, the following conditions must be met: 

    Contact resistance: Change does not exceed 20% of the initial value (the initial value is usually less than 100Ω, and the final value is less than 200Ω)
    Insulation resistance: Maintain > 10MΩ (tested at 100VDC)
    Operating force: Within ±20% of the initial value
    Appearance: No cracking, damage, or permanent deformation
    Bounce ratio: > 50%

    Sampling frequency
    Every 100,000 tests, the following items will be sampled: 

    Contact resistance (four-wire Kelvin method measurement)
    Insulation resistance (50-100VDC, for 60 seconds)
    Visual inspection (observation of silver paste lines and contact wear with a magnifying glass)
    Operation force test (measured by a force sensor)

    Backlight lifespan test
    This is the core test item that distinguishes the backlighting membrane switch from the ordinary membrane switches. 
    Testing equipment
    Integral sphere + spectrometer: Measures luminance (cd/m²) and color temperature (K)
    Luminance meter/illuminance meter: Quickly measures relative changes in luminance
    Constant temperature and humidity chamber: Conducts accelerated aging tests
    DC power supply: Provides a constant current for the backlight

    Testing method
    Constant temperature and constant illumination aging test
    In a 25°C environment, continuously illuminate the backlight at the rated current
    Measure the brightness and color temperature every 24 hours
    Record the brightness decay curve until the brightness drops to 70% of the initial value (L70 standard)

    High-temperature accelerated aging test
    Place the sample in a constant temperature box and set the temperature to 85°C (or the maximum operating temperature of the product)
    Keep the backlight illuminated at the rated current
    Measure the brightness every 12 to 24 hours
    Calculate the lifespan at room temperature based on the Arrhenius model

    Switch cycle test
    Simulate actual usage scenario: backlight on for 30 seconds → off for 30 seconds in a cycle
    Number of cycles: 100,000 to 500,000 times
    Monitor whether LED solder joints show fatigue fracture

    Criteria for judgment

    Indicators   Qualification Standards
    Brightness attenuation (1000 hours)  ≤ 15% (LGF scheme) / ≤ 20% (traditional LED scheme)
    Color temperature drift  ΔCCT ≤ 300K
    Luminous uniformity  Difference in brightness between the center and the edge ≤ 20%
    LED failure rate 0 failures (no dead lamps allowed)
    Welding point reliability No cracking, no false welding

    The actual measurement results show that after the LGF (light guide film) solution has been continuously operating in an environment of 85°C/85%RH for 2000 hours, the brightness decline does not exceed 15%, which is superior to the traditional multi-LED solution. 
    Comprehensive lifespan test (most critical)
    Mechanical pressing and backlight illumination are carried out simultaneously to assess the interaction effect between the two:

    Test scenario
    The button is continuously pressed at a frequency of 60 times per minute.
    The backlight is continuously lit at the rated current.
    Environmental temperature: Tested at high temperature (+70°C) and low temperature (-20°C).
    Test duration: 72 to 168 hours (acceleration test)

    Key Monitoring
    Thermal accumulation effect: Whether the LED heat generation accelerates the aging of the silver paste circuit
    Mechanical stress impact on the backlight: Whether repeated pressing causes fatigue of the LED solder joints
    Backlight uniformity change: Whether the light guide film in the pressed area develops indentations or light attenuation
    Power consumption change: Whether the backlight current drifts over time

    Environmental reliability testing
    Before and after the life test, the following environmental tests are also required:

    Test item   Conditions  Duration Purpose
    High-temperature storage 85°C 168 hours Evaluate the material's heat resistance
    Low-temperature storage -40°C  168 hours  Evaluate the material's low-temperature resistance
    Temperature and humidity cycling  -40°C ↔ 85°C, 10 cycles Approximately 240 hours  Evaluate the effect of thermal expansion and contraction
    High-temperature and high-humidity 85°C/85%RH  168 hours  valuate the wet heat aging
    Vibration test   10-55Hz, 1.5mm amplitude 2 hours per axis Evaluate the structural firmness

    After the environmental tests are completed, a complete mechanical lifespan inspection will be conducted again to confirm that the environmental stress has not caused any performance degradation. 
    Test Process Overview
    Sample Preparation (5-10 pieces)
    ↓
    Initial Performance Test (record baseline data)
    ↓
    ┌───────────────────────────────────────┐
    │ Parallel Test                    │
    │  ├─ Mechanical Life Test (1 million cycles)  │
    │  ├─ Backlight Constant Brightness Aging (1000 hours)  │
    │  └─ Comprehensive Life Test (168 hours)  │
    └───────────────────────────────────────┘
    ↓
    Environmental Reliability Test (temperature and humidity cycling, etc.)
    ↓
    Final Performance Test (compare with baseline)
    ↓
    Issue Test Report

    Reference standard
    ASTM F3091: Test Specifications for Membrane Switches (Pressing Frequency, Force, and Rate)
    IEC 61058 Series: General Standards for Switching Equipment
    IEC 61000 Series: Electromagnetic Compatibility and Mechanical Durability in Industrial Environments
    GB/T 16915.1: Standards for Household and Similar Use Switches
    LM-80: Test Standard for Lumen Maintenance Rate of LED Light Sources (Reference for Backlight Part)

    💡 Summary: The lifespan test for the backlighting membrane switch = Mechanical lifespan (1 million presses, monitoring contact resistance and operating force) + Backlight lifespan (1000 hours of constant illumination, monitoring brightness attenuation and color temperature drift) + Comprehensive lifespan (simultaneous operation of mechanical and backlight, evaluating the interaction effect) + Environmental reliability (temperature and humidity cycling, high temperature and high humidity). Among them, the backlight part is the key test item that distinguishes it from ordinary membrane switches. It is recommended to pay particular attention to the reliability of the LED solder joints and the indentation of the light guide film.