What material should be chosen for the waterproof gasket of the membrane switch?
The waterproof rubber ring of the membrane switch (usually referring to the sealing ring at the tail connector outlet or the gasket between the panel and the housing) requires a comprehensive consideration of factors such as sealing method, environmental requirements, and cost. Based on your application scenario, the following are some suggestions for the selection of mainstream materials:
1. Preferred recommendation: Silicone
Applicable scenarios: The waterproof sealing for the vast majority of membrane switches, especially in scenarios that require high elasticity, wide temperature range, and no toxicity or odor (such as medical, outdoor, and consumer electronics).
Advantages:
Excellent elasticity: Compression deformation rate is low (<10%), able to maintain sealing pressure for a long time, suitable for dynamic sealing.
Wide temperature range: -60°C to 230°C (short-term), -40°C to 180°C (long-term), able to adapt to extreme temperature differences in outdoor and industrial environments.
Good weather resistance: Strong resistance to ultraviolet (UV) and ozone aging, less prone to cracking in outdoor long-term use.
Non-toxic and odorless: Compliant with FDA, RoHS and other environmental regulations, suitable for medical and food contact equipment.
Good processability: Easy to be molded through injection or compression molding, customizable for complex shapes and colors.
Disadvantages: Not recommended for long-term contact with oil (such as fuel, lubricating oil) and strong acid and alkali environments.
Typical applications: Outdoor cabinets, medical equipment, consumer electronics, smart home panels.
2. Preferred for oil and chemical resistance: Fluorine rubber (FKM / Viton™)
Applicable scenarios: Requires contact with oils, solvents, strong acids, and strong bases in harsh industrial environments (such as chemical plants, car engine compartments, pharmaceutical equipment).
Advantages:
Extremely strong chemical resistance: Resistant to acids, alkalis, solvents, fuel, lubricating oil, etc., almost unaffected by chemical corrosion.
Excellent high-temperature resistance: Can reach above 250℃, suitable for high-temperature industrial environments.
Effective sealing against penetration: Can effectively prevent liquids or gases from penetrating the seal.
Disadvantages:
High cost: The price is 2-3 times that of silicone rubber.
Average low-temperature resistance: Usually usable above -20℃, elasticity decreases at low temperatures.
Single color: Usually black, with limited color options.
Typical applications: Chemical equipment, car fuel systems, aerospace seals.
3. Preferred for low-temperature resistance: Ethylene Propylene Diene Monomer (EPDM) rubber
Application scenarios: Low-temperature environments (such as refrigeration equipment, outdoor in the north), humid environments (such as bathroom equipment, steam sterilizers).
Advantages:
Outstanding low-temperature resistance: Can withstand temperatures as low as below -50℃ while maintaining elasticity.
Excellent weather resistance and ozone resistance: Suitable for long-term outdoor exposure.
Good water resistance: Does not expand or deform when immersed in water for a long time.
Good chemical resistance: Has good resistance to alcohols, ketones, weak acids, and weak bases.
Disadvantages:
Poor oil resistance: Will expand and be damaged when in contact with mineral oil or fuel.
Average high-temperature resistance: Usually does not exceed 150℃.
Typical applications: Refrigeration equipment, bathroom shower heads, automotive radiator seals.
4. Low-cost general-purpose option: Nitrile rubber (NBR)
Application scenarios: Suitable for large-scale applications where cost is a concern and exposure to oils but temperatures are not extreme (such as ordinary industrial equipment, automotive seals).
Advantages:
Good oil resistance: Suitable for environments in contact with fuel and lubricants.
Low cost: One of the lowest-cost options among rubber seals.
Good wear resistance: Suitable for scenarios with frequent friction.
Disadvantages:
Narrow temperature range: -40°C to 120°C.
Poor water resistance: Long-term exposure to water may lead to performance degradation.
Average weather resistance: Prone to aging outdoors and requires the addition of anti-aging agents.
Typical applications: Automotive fuel systems, hydraulic equipment, ordinary industrial control panels.
5. Special Scenario: PTFE Coated Sealing Ring
Applicable Scenarios: Situations requiring extremely low friction coefficient, resistance to strong corrosion or high cleanliness (such as in food processing, semiconductor equipment).
Advantages:
Extremely resistant to all chemicals: PTFE (polytetrafluoroethylene) is one of the most chemically inert materials.
Extremely low friction coefficient: Suitable for sliding seals requiring low friction.
Extremely wide temperature range: -80℃ to 260℃.
Disadvantages:
Poor elasticity: PTFE itself has no elasticity and needs to be combined with rubber (such as EPDM, FKM) for use.
High cost: Difficult to process and expensive.
Typical Applications: Chemical pipelines, food machinery, semiconductor equipment seals.
Summary: How to make a quick selection?
| Environmental conditions | Recommended material | Reasons |
| General outdoor, medical, consumer electronics | Silicone | Overall performance is the best, resistant to weathering, temperature, non-toxic, and cost is moderate. |
| Contacting oil, solvents, strong acids and alkalis | Fluororubber (FKM) | Has the strongest chemical resistance, can withstand high temperatures. |
| Extremely cold environment, water vapor environment | Butyl ethylene propylene rubber (EPDM) | Outstanding performance in low temperature, water resistance, and ozone resistance. |
| Cost-sensitive, contact with oil | Butyl rubber (NBR) | High cost-effectiveness, good oil resistance. |
| Strong corrosion, high cleanliness | PTFE coated sealing ring | Strong chemical inertness, lowest friction coefficient. |
